LTE Cat.1 7 Click
LTE Cat.1 7 Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.
Click Library
- Author : Stefan Filipovic
- Date : Oct 2024.
- Type : UART type
Software Support
Example Description
Application example shows device capability of connecting to the network and sending SMS or TCP/UDP messages, or retrieving data from GNSS using standard "AT" commands.
Example Libraries
- MikroSDK.Board
- MikroSDK.Log
- Click.LTECat17
Example Key Functions
- ltecat17_cfg_setup Config Object Initialization function.
void ltecat17_cfg_setup(ltecat17_cfg_t *cfg)
LTE Cat.1 7 configuration object setup function.
LTE Cat.1 7 Click configuration object.
Definition ltecat17.h:179
- ltecat17_init Initialization function.
err_t ltecat17_init(ltecat17_t *ctx, ltecat17_cfg_t *cfg)
LTE Cat.1 7 initialization function.
LTE Cat.1 7 Click context object.
Definition ltecat17.h:155
- ltecat17_set_sim_apn This function sets APN for sim card.
void ltecat17_set_sim_apn(ltecat17_t *ctx, uint8_t *sim_apn)
Set sim card APN.
- ltecat17_cmd_run This function sends a specified command to the Click module.
void ltecat17_cmd_run(ltecat17_t *ctx, uint8_t *cmd)
LTE Cat.1 7 cmd run function.
- ltecat17_set_power_state This function sets a desired power state by toggling PWR pin with a specific time for high state.
void ltecat17_set_power_state(ltecat17_t *ctx, uint8_t state)
LTE Cat.1 7 set power state function.
Application Init
Initializes the driver and logger.
{
log_cfg_t log_cfg;
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
{
log_error( &logger, " Communication init." );
for ( ; ; );
}
log_info( &logger, " Application Task " );
log_printf( &logger, ">>> APP STATE - POWER UP <<<\r\n\n" );
}
#define LTECAT17_MAP_MIKROBUS(cfg, mikrobus)
MikroBUS pin mapping.
Definition ltecat17.h:139
void application_init(void)
Definition main.c:219
#define MIKROBUS_POSITION_LTECAT17
Definition main.c:65
@ LTECAT17_POWER_UP
Definition main.c:99
Application Task
Application task is split in few stages:
- LTECAT17_POWER_UP:
Powers up the device, performs a device factory reset and reads system information.
- LTECAT17_CONFIG_CONNECTION:
Sets configuration to device to be able to connect to the network (used only for SMS or TCP/UDP demo examples).
- LTECAT17_CHECK_CONNECTION:
Waits for the network registration indicated via CEREG command and then checks the signal quality report (used only for SMS or TCP/UDP demo examples).
- LTECAT17_CONFIG_EXAMPLE:
Configures device for the selected example.
- LTECAT17_EXAMPLE:
Depending on the selected demo example, it sends an SMS message (in PDU or TXT mode) or TCP/UDP message or waits for the GPS fix to retrieve location info from GNSS. By default, the TCP/UDP example is selected.
{
switch ( app_state )
{
{
{
log_printf( &logger, ">>> APP STATE - CONFIG CONNECTION <<<\r\n\n" );
}
break;
}
{
if (
LTECAT17_OK == ltecat17_config_connection( <ecat17 ) )
{
log_printf( &logger, ">>> APP STATE - CHECK CONNECTION <<<\r\n\n" );
}
break;
}
{
if (
LTECAT17_OK == ltecat17_check_connection( <ecat17 ) )
{
log_printf( &logger, ">>> APP STATE - CONFIG EXAMPLE <<<\r\n\n" );
}
break;
}
{
if (
LTECAT17_OK == ltecat17_config_example( <ecat17 ) )
{
log_printf( &logger, ">>> APP STATE - EXAMPLE <<<\r\n\n" );
}
break;
}
{
ltecat17_example( <ecat17 );
break;
}
default:
{
log_error( &logger, " APP STATE." );
break;
}
}
}
@ LTECAT17_OK
Definition ltecat17.h:205
void application_task(void)
Definition main.c:252
@ LTECAT17_CONFIG_CONNECTION
Definition main.c:100
@ LTECAT17_EXAMPLE
Definition main.c:103
@ LTECAT17_CHECK_CONNECTION
Definition main.c:101
@ LTECAT17_CONFIG_EXAMPLE
Definition main.c:102
In order for the examples to work (except GNSS example), user needs to set the APN and SMSC (SMS PDU mode only) of entered SIM card as well as the phone number (SMS mode only) to which he wants to send an SMS. Enter valid values for the following macros: SIM_APN, SIM_SMSC and PHONE_NUMBER_TO_MESSAGE.
Example:
- SIM_APN "internet"
- SIM_SMSC "+381610401"
- PHONE_NUMBER_TO_MESSAGE "+381659999999"
Application Output
This Click board can be interfaced and monitored in two ways:
- Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
- UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.
Additional Notes and Information
The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.